An advanced multi-channel microphone automixer with built-in support for Dante audio networking, VoIP conferencing, a Telco interface, and the latest audio DSP algorithms.
Audio: Digital Audio, 2 x 2 bidirectional channels
Sample Rate: 48kHz
Sample Bit Depth: 24-Bit
Compatible: USB 2.0, USB 3.0
TELEPHONE
Port Type: RJ11
Frequency Response:
- Mic/Line Input to Telephone Out: 250Hz – 3.4kHz , +/- 2dB, 4dBu
- Telephone In to Mic/Line Out: 250Hz – 3.4kHz, +/- 2dB, -15dBu
THD + N:
- Mic/Line Input to Telephone Out: <0.1% @ 4dBu
- Telephone In to Mic/Line Out: <0.3% @ -15dBu
Dynamic Range:
- Mic/Line Input to Telephone Out: >67dBu
- Telephone In to Mic/Line Out: >87dBu
REN: Ringer Equivalent Number 0.2
Transhybrid Balance: 30dB (1kHz, all AC terminations)
VOIP
Port Type: RJ-45, 10/100Mbps Ethernet Network, Auto Negotiation
Audio: 5 Lines
Codec: G.711 uLaw, G.711 ALaw, G.722
ETHERNET
Port Type: RJ-45, 10/100Mbps Ethernet Network, Auto Negotiation
IP address: IPv4 (IPv6 upgradeable through future s/w, f/w upgrade)
DANTE™ and AES67 AUDIO
Port Type: RJ-45 Gigabit Ethernet connectors for Primary and Secondary Ports
Audio: Digital Audio, 16 x 16 bidirectional channels
Sample Rate: 48 kHz / 96 kHz
Sample Bit Depth: 24-Bit
AES67 Mode: Enabled through Dante controller software
C-LINK EXPANSION BUS
Ports Type: RJ-45 (Cat5e or Cat6)
C-Link In & Out: Proprietary Expansion Bus
Audio: 64 Expansion channels
Cable: Solid core, factory terminated Cat 5e or 6 cable
Distance: Up to 150’ (45M)
P-LINK PERIPHERAL BUS
Ports Type: RJ-45 (Cat5e or Cat6)
P-Link In & Out: Proprietary Peripheral Bus
PoE In:
- P-Link In Port
- PoE 802.3af Mode B, Midspan
- Power on “spare pairs” 4,5 and 7,8
- Input voltage range: 48V to 56V
Audio: Up to 3 Beamforming Microphone Array 2 units + up to 3 DIALOG 20 Wireless Receiver units + Up to 3 USB Expander units + Up to 3 GPIO Expander units
Cable: Solid core, factory terminated Cat 5e or 6 cable
Distance: Up to 200’ (60M)
RS-232
Port Type: DB9 Female
Settings: 9600/19200/38400/57600/115200 Baud; Serial Echo; Flow Control
Support: Serial commands or VISCA camera control
GPIO
Port Type: 5.08mm Green color Phoenix/Euroblock type male header
Support: Control, Status, Variable Voltage Control
Power Pin: 5V DC @ 350mA Power Source
Pin 1 to 4:
- Open Collector Outputs: 40VDC @ 250mA
- Active Outputs (Source/Sink): 5VDC @25mA
- Logic Inputs: 40.2kΩ pull up
- Variable Voltage Control Inputs: 5VDC max
Ground Pin: GND
USB CONTROL
Port Type: USB-B connector
Location: Front Panel
Compatible: USB 2.0, USB 3.0
LEDs
Location: Front Panel
Status LED:
- Off: Unit still initializing
- Blue - Fast Blinking: Stack Syncing in progress
- Blue - Slow Blinking: Unit not configured
- Blue - Solid: Configured unit
- Red - Fast Blinking: Stack Sync error
Locate LED: Blue - Blinking: Unit “Locate” command received
Power LED: Blue - Solid: Unit is powered on
LOCATE BUTTON
Sensor Type: Capacitive Touch Button
Location: Front Panel
POWER & THERMAL
Port Type: AC Inlet
Mains Voltage: 100-240V AC, 50/60Hz
Power Consumption: 50 Watts Typical
Thermal: 170 BTU/Hr Typical
Operating Temperature: 14°F (-10°C) to 104°F (40°C) Ambient Temperature
DIMENSION & WEIGHT
RU size: 1 RU
Width x Depth x Height:
1. Without rack-ears: 17.1 x 10.7 x 1.7 “ (431 x 273 x 44 mm)
2. With rack-ears:19.1 x 10.7 x 1.7 “ (483 x 273 x 44 mm)
Unit Weight: 9.3 lbs (4.2 kg) (Approximately)
Shipping Weight: 13.8 lbs (6.3 kg) (Approximately)
PACKAGE
Power Cord: 6’ (1.8M), Grounded, Qty 1
Input Connectors: Terminal Block Connector, 3 Position (Orange), Qty 12
Output Connectors: Terminal Block Connector, 3 Position (Black), Qty 8
GPIO Connector: Terminal Block Connector, 6 Position (Green), Qty 1
C-Link Cable: RJ-45 To RJ-45 Cable, 18” (45.7cm), Qty 1